Posted in

How to seal purlin connections against moisture?

If you’ve ever worked with metal roofing or wall systems, you know C and Z purlins are the unsung heroes holding everything together. They’re lightweight, durable, and engineered to span long distances without sagging—perfect for everything from agricultural barns to commercial warehouses. But here’s the thing: their biggest strength (that sleek, load-bearing steel design) can also be their biggest weakness when it comes to moisture. Purlins connect to each other, to rafters, or to beams, and if those connections aren’t sealed right, water seeps in. Not only does that lead to rust on the steel itself, but it also damages the insulation, roofing materials, and even the structure over time. As a C and Z purlin supplier who’s been in this game for 12 years, I’ve seen more projects go sideways because of bad connection sealing than any other issue. I’m writing this not with textbook jargon, but with real-world lessons I’ve learned from working with contractors, builders, and roofers across the Midwest. Let’s break down how to seal purlin connections against moisture the right way, so you don’t have to deal with costly callbacks or structural headaches down the line. C And Z Purlin

First, let’s talk about why purlin connections are such moisture hotspots. C and Z purlins aren’t just flat pieces of steel—they have a unique shape with flanges and webs that create small gaps, overlaps, and screw holes where water can sneak in. Unlike solid beams, their interlocking design means there are multiple contact points that, if not sealed, act like a sieve. I remember a job three years ago for a large cattle barn in Iowa. The builder rushed the sealing, used generic caulk he had lying around from a plumbing supply store, and skipped adding a sealant to the lap joints where the Z purlins overlapped. By the end of the first winter, melting snow seeped through those gaps, pooled on the purlins’ inner flanges, and caused rust to eat through the steel before we even finished the insulation. That job cost the builder $45,000 in repairs, and we ended up replacing the faulty purlins with ones that came pre-sealed at the factory. That’s when I realized that sealing purlin connections isn’t an afterthought—it’s a critical part of the installation, not something you do at the end when everyone’s tired.

So where do you even start? The first step is to prep the connection area correctly. A lot of builders skip this, but I can’t stress it enough: you can’t seal a dirty purlin. Before applying any sealant or fasteners, you need to clean every connection point where two purlins meet or where a purlin attaches to a support beam. That means removing dirt, dust, mill scale (the oily residue left on new steel), rust, and even loose paint. I always recommend using a wire brush for light dirt and a pressure washer (set to low pressure to avoid damaging the purlin’s shape) for caked-on grime. If the purlin has any existing rust, use a sandblaster or heavy-grit sandpaper to get it down to bare metal—rust stops when you get to the clean steel, not just the surface. I also suggest wiping the area with a rag dipped in isopropyl alcohol to remove any leftover oil or cleaning product residue. Sealant won’t stick to a surface that’s even slightly greasy, no matter how hard you try. I’ve seen contractors take shortcuts here, and every single time, the sealant peels off within a year. Prep work might take an extra hour per connection, but it saves you from months of headaches later.

Next, choose the right sealing materials for the job. Not all sealants are created equal, and using the wrong one is a quick way to end up with leaks. As a C and Z purlin supplier, I test three main types of sealants regularly, and each has its place. The first is butyl rubber tape. This is my go-to for lap joints—where two Z purlins overlap, or a C purlin connects end-to-end. Butyl tape is sticky, flexible, and stays pliable even in extreme temperatures, which is perfect for areas where the purlin might expand or contract with weather changes. I apply a 1/8-inch thick strip of butyl tape along the entire length of the overlapping flange, making sure to press it down firmly to squeeze out any air bubbles. The key here is to not stretch the tape when you apply it—stretching makes it thinner in spots, which can tear or let water through. For example, when we supply pre-cut Z purlins, we now include pre-cut butyl tape strips for every lap joint, because builders were complaining about wasting tape or applying it unevenly. The second sealant I recommend is polyurethane sealant. This is best for screw holes or smaller gaps, like where a purlin attaches to a support beam. Polyurethane is waterproof, flexible, and adheres well to steel, but you have to get the right type—look for one labeled “metal-compatible” and “UV-resistant.” Regular polyurethane breaks down in sunlight, so if you’re sealing a connection on an exterior wall, skip the interior-grade stuff. The third option is silicone, but I only use this for non-structural, interior connections. Silicone is waterproof and flexible, but it doesn’t stick well to some types of steel, and it’s hard to paint over if you need to finish the purlin, so I avoid it for exterior projects.

Now, let’s talk about specific connection types and how to seal each one correctly. Purlin connections fall into three main categories: end laps, side connections, and fastener holes. Each needs a different approach. End laps are when two purlins meet at their ends and overlap, usually by 12 to 18 inches. For these, first clean both overlapping flanges, then apply a full strip of butyl tape along the inside of the top flange (the side that faces the roof or wall). Make sure the tape covers the entire overlap, with no gaps in the middle or at the ends. Then, when you bolt or screw the two purlins together, the butyl tape compresses to create a watertight seal. If you use self-drilling screws for this, I also recommend running a bead of polyurethane sealant around the screw heads after you drive them in—this adds an extra layer of protection. The second connection type is side connections, which is when a purlin attaches perpendicularly to another purlin (like when a C purlin connects to a Z purlin at a corner). For these, you have to seal both the top and bottom flanges of the intersecting point. Clean both sides of the connection, apply butyl tape to the surface where the two purlins meet, then fasten them, and again, add a bead of polyurethane around each fastener. A common mistake here is only sealing the top side—water can get in between the two purlins from the bottom if you skip that. The third, and most critical, connection to seal is the fastener holes. Every screw or bolt you drive through a purlin creates a small hole, and that’s one of the easiest places for water to get in. After you drive the fastener, wait a few minutes for any metal shavings to fall away, then apply a 1/4-inch bead of polyurethane or butyl rubber sealant around the head. Make sure the sealant covers the entire edge of the fastener and spreads slightly onto the purlin’s surface so there are no gaps. I always tell builders to do this by hand, not with a caulking gun’s nozzle—you have more control, and less chance of missing a spot.

Wait a second—what about pre-sealed purlins? A lot of builders don’t know that many C and Z purlin suppliers offer pre-sealed options, which save you so much time and hassle. I started offering pre-sealed purlins five years ago, after hearing from contractors that they were spending 20% of their installation time sealing connections. Pre-sealing doesn’t mean slapping on a random layer of caulk—it means applying industry-grade butyl tape to all lap joints and coating fastener holes at the factory, in a controlled environment where the surface is perfectly clean. This is way better than sealing on-site because you don’t have to worry about dirty hands, weather conditions making sealant not stick, or skipping a spot. For example, on a 10,000-square-foot roof, pre-sealed purlins can cut installation time by two days, and they come with a 10-year moisture seal warranty, which is something you can’t get from on-site sealing. I always explain to builders that paying a little extra for pre-sealed purlins saves them money in the long run—less labor, fewer callbacks, and no rust-related repairs.

But even with all this, there are common mistakes I see every single day that can ruin a good sealing job. Let’s go over those so you can avoid them. First, using too little sealant. A lot of builders skimp on tape or caulk to save money, but a thin strip of butyl tape won’t stop water from seeping through. I recommend following the manufacturer’s instructions for thickness—usually 1/8-inch for tape, 1/4-inch for sealant. Second, not accounting for thermal expansion. Steel expands and contracts with temperature changes—up to 0.6 inches per 100 feet in temperature extremes. If you seal a purlin too tightly without leaving a small gap, the sealant will crack when the steel moves, creating leaks. I always tell builders to leave a 1/8-inch gap between the sealant and the edge of any fastener or connection point to allow for movement. Third, sealing when it’s too hot or too cold. Sealants have a temperature range they work best in—most butyl tape and polyurethane sealants work between 40°F and 90°F. If you apply sealant when it’s 30°F outside, it won’t cure properly, and if you apply it when it’s 100°F, it will dry too fast and crack. I check the weather forecast for at least the next 48 hours before I suggest sealing—you need time for the sealant to cure, and no rain or snow forecast during that period. Fourth, using the wrong sealant for the climate. If you’re building in a rainy, humid area, you need a more UV-resistant sealant than if you’re building in a dry, sunny desert. I work with builders to match sealant to their local weather, because a one-size-fits-all approach never works.

Now, let’s talk about long-term maintenance, because sealing purlin connections isn’t a “set it and forget it” job. Even the best sealants will degrade over time, so you need to inspect connections every two years for signs of wear. What should you look for? Cracks in the sealant, peeling tape, rust spots around fastener holes, or water stains on the roof or wall inside the building. If you notice any of these, you can touch up the sealant—just clean the area, apply a new layer of polyurethane, and you’re good to go. I also recommend re-sealing lap joints every 10 years, even if you don’t see signs of damage, because that’s the average lifespan of most sealants. As a supplier, I provide maintenance guides for every set of purlins we sell, so builders don’t have to guess what to do.

At the end of the day, sealing purlin connections against moisture is all about being intentional. It’s not a chore—it’s a step that protects the entire structure you’re building. I’ve seen projects that cut corners on sealing end up failing in 5 years, and I’ve seen projects that take the time to do it right last 30 years or more. If you’re working on a new construction, a roof replacement, or adding an addition, don’t let bad sealing cost you time and money. If you have questions about which purlins are right for your project, what sealant to use, or how to get the job done correctly, feel free to reach out to our team for guidance. We work with contractors and builders of all sizes, from small barn projects to large commercial warehouses, and we’re here to help you get it right the first time.

Sandwich Puf Roof Panel References

  1. Steel Construction Manual, American Institute of Steel Construction, 15th Edition, 2017.
  2. Roofing and Waterproofing Manual, National Roofing Contractors Association, 6th Edition, 2020.
  3. Corrosion Control in Metal Building Structures, Steel Buildings Institute, 2019.
  4. “Sealing Metal Connections for Moisture Resistance,” Journal of Construction Engineering and Management, Vol. 145, No. 8, 2019.

Shenyang Qiangyun Color Steel & Steel Structure Co., Ltd.
Shenyang Qiangyun Color Steel & Steel Structure Co., Ltd. is one of the most professional c and z purlin manufacturers and suppliers in China. Please feel free to wholesale advanced c and z purlin in stock here and get pricelist from our factory. All customized products are with high quality and competitive price.
Address: 10#, Hongxing Road, Yuhong District, Shenyang, Liaoning, China
E-mail: syqysteel@gmail.com
WebSite: https://www.qysteelstructure.com/