Hey everyone, Litz Wire

If you’ve ever worked with high-frequency electronics—think transformers for EV chargers, induction heating coils, or even those tiny chargers that charge your phone super fast—you’ve probably heard of Litz wire. It’s not just some fancy buzzword; it’s the stuff that makes those devices work better by cutting down on that annoying skin effect that kills efficiency. As a Litz wire supplier, I get asked all the time “how do you actually make Litz wire?” Most people think it’s just twisting a bunch of wires together, but there’s way more to it than that. Let me break it down like I would to a new engineer who just walked into our shop—no fancy jargon, just real talk from someone who’s been doing this for over a decade.
First, let’s get one thing straight: what Litz wire is, exactly. Skin effect, for those who don’t geek out on AC current, is when high-frequency electricity doesn’t flow evenly through a single wire. It all bunches up on the outer surface, so the actual conductive area is way smaller than the wire’s total cross-section. That means more resistance, more heat, and less power going where you need it. Litz wire fixes this by using lots of thin, insulated strands instead of one thick wire. But here’s the key—those strands aren’t just twisted randomly. Every single step is calculated to make sure current flows through each strand equally, so you get maximum conductivity at high frequencies.
Let’s start with the raw materials because not all wires are created equal. We don’t use just any copper here. Most of our Litz wire is made from oxygen-free copper (OFC)—it’s purer than regular copper, so it has way less impurities that cause resistance, especially at high frequencies. We also use different strand gauges depending on what the customer needs. For example, someone making a small wireless charger might use 40-gauge strands (super thin, like hair), while a big induction heater for a foundry needs thicker strands, around 18-gauge. The insulation on each strand matters too—we use a thin, durable enamel called polyurethane, or sometimes polyimide for higher heat applications. That insulation is just a few microns thick, so it doesn’t take up too much space, but it’s enough to keep strands from touching each other until we’re ready to twist them.
The first real step in the process is strand selection and counting. We don’t just grab a spool and count as we go—we have precision machines that pull off exactly the number of strands a customer orders. For example, if a customer needs 100 strands for a 5mm Litz wire, we set the machine to pull 100 individual strands, each coming off their own spool, all at the same speed. It’s crucial that all strands are the same length and tension here. If one strand is a little tighter than the others, it’ll stretch more, get thinner, and have more resistance—undermining the whole point of Litz wire. Our machines have tension sensors that adjust on the fly, so every strand stays consistent. No shortcuts here; we’ve had customers come to us with bad Litz wire from other suppliers where strands were uneven, and it caused their transformers to overheat. That’s the kind of mistake we don’t make.
Next up is the first twist step, which we call “laying up” the strands. Wait, but not just twisting them once—there’s a whole sequence here. Let’s say we’re making a simple 7-strand Litz wire. If you just twist all 7 together in one big twist, you get what’s called a single-lay Litz, but that’s not ideal for higher frequencies. Oh right, lay length is a big deal—lay length is how far you twist before the pattern repeats. For high-frequency applications (like above 10kHz), we use multiple layers of twisting, each with a different lay direction. That’s called a “bifilar” or “trifilar” lay, depending on how many layers you have. Why? Because each strand has to move to a different position on the outside of the bundle every twist. If strands stayed on the outside the whole time, they’d carry more current than the ones on the inside, which brings back the same skin effect problem we were trying to fix. It’s like a shuffle for wires—each strand takes a turn being on the outer part of the bundle, so current is distributed evenly. Our twist machines are computer-controlled, so we can set the exact lay length for each layer within a fraction of a millimeter. If we get the lay length even a little off, the Litz wire might not work at the frequency the customer needs. We test every batch on our impedance analyzers to make sure it’s spot-on before it leaves the shop.
Wait, what about when we need more strands than can fit in a single bundle? Like, if someone needs 500 strands for a large transformer? Then we have to make sub-bundles first. For example, we might make 10 sub-bundles of 50 strands each, then twist those 10 sub-bundles together into the final Litz wire. That’s called a “second lay” or “multi-lay” process. The lay direction for the sub-bundles has to be opposite to the lay direction of the individual strands. If we twist the strands clockwise and then twist the sub-bundles clockwise, the whole thing would just unravel. Yeah, I learned that the hard way early on—ruined a whole spool of expensive copper, and my boss wasn’t happy. Now we have a checklist for every job: strand count, lay directions, lay lengths, insulation thickness. No guessing.
Once we have the twisted bundle, we can’t just leave it naked. Most customers need the whole Litz wire insulated too, right? So the next step is applying the outer jacket. We use either PVC, polyethylene, or sometimes Teflon for high-heat environments. The jacket is applied with an extruder—we heat the plastic until it’s soft, then push it through a die that fits around the Litz wire bundle, so it coats evenly. Again, thickness is important—too thin and it tears during installation, too thick and it makes the wire too bulky for tight spaces, like inside a smartphone. We also have to make sure the jacket adheres well to the inner insulation of the strands, but not so well that it’s hard to strip off when the customer is assembling their product. For medical devices, we even use radiation-cured jackets that are more flexible and resistant to chemicals, since those devices go through sterilization processes.
Wait, there’s another step I almost forgot: annealing. Copper gets work-hardened when you twist it, which makes it stiffer, harder to bend, and can even make it brittle over time. So after we twist the strands, we run the Litz wire through an oven to anneal it—heat it up to around 200-300°C, which relieves that tension from twisting. That makes the wire way more flexible, which is crucial for applications where it’s going to be bent over and over, like in EV batteries where wires have to flex as the battery packs expand and contract. We also have to cool it down slowly, not just blast cold air on it, because fast cooling can cause stress in the wire too. We test flexibility every batch by bending it 180 degrees around a mandrel of a certain size—if it cracks, it’s not annealed enough. Simple test, but it catches a lot of problems.
Now, let’s talk about quality control, because that’s what separates us from the random guy in a garage making Litz wire in his basement. Every single batch we make goes through a series of tests. First, we check the strand count under a microscope—even one less strand can throw off the resistance. Then we measure the DC resistance, because that’s a direct indicator of conductivity. If the resistance is higher than it should be, that means a strand is broken or not making good contact. For high-frequency work, we do an impedance sweep from 1kHz to 1MHz to make sure the inductance and capacitance are where they need to be. We also pull the jacket to make sure it adheres properly, and check for any insulation defects on the strands—even a tiny pinhole can cause a short when the wire is under load.
I know this sounds like a lot of steps, and it is. That’s why Litz wire isn’t cheap—you’re not just paying for copper, you’re paying for the precision, the quality control, and the expertise to get the twists and lays right. As a supplier, we work closely with customers to customize Litz wire for their specific needs. For example, a customer making a wireless power transfer system for an electric bus needed Litz wire that could handle high currents at 100kHz, so we used thicker strands and adjusted the lay length to minimize losses at that specific frequency. Another customer making a small medical implant needed super thin Litz wire (2 strands of 48-gauge) that was flexible enough to implant without damaging tissue, so we used a special flexible enamel insulation.
A lot of people ask why we don’t just use automated machines that twist faster. Well, speed matters, but not if it ruins the wire. If you twist too fast, the strands can slip, the lay length gets uneven, and the insulation on the strands can scratch or wear down. We run our machines at a speed that’s just right—fast enough to be efficient, but slow enough to keep quality high. We also have a team of technicians who monitor every spool as it comes off the line, checking for any visual defects, from a misaligned strand to a thin jacket.
Here’s the thing: Litz wire is a niche product, but it’s super important. Without good Litz wire, high-frequency electronics would be less efficient, run hotter, and have shorter lifespans. As someone who’s been in this business for 12 years, I take pride in every batch we send out. I know our customers rely on us to get the Litz wire right, because if their product fails because of bad wire, their reputation is on the line too.

If you’re working on a project that needs Litz wire—whether it’s a small hobbyist build or a big industrial application—don’t hesitate to reach out. We can help you figure out the right strand count, gauge, lay length, and insulation for your specific frequency, power level, and application. No one-size-fits-all here, and we’re happy to walk you through every step to make sure you get exactly what you need.
Enameled Flat Wire References
T. H. Ortmeyer, Electrical Principles of High-Frequency Design, Wiley, 2018.
Litz Wire Manufacturing Standards, IEC 60228, 2020.
"Understanding Skin Effect and Litz Wire Usage," Electronics Applications Journal, Vol. 45, No. 3, 2021.
Tianjin Jingwei Power Technology Co., Ltd.
As one of the most professional litz wire manufacturers and suppliers in China, our products have good reputation in the market. We warmly welcome you to buy durable litz wire for sale here from our factory. Good service and quality products are available.
Address: No.1 Chuangxin Rd. Xiaozhan Industrial Park, Jinnan District, Tianjin, China
E-mail: info@jwdc.cn
WebSite: https://www.jwdcs.com/