Posted in

how to install a trailer jack on a bumper pull

If you’ve ever hitched up a trailer on your own, you know the struggle of balancing that heavy tongue while fumbling with latches, couplers, and safety chains. Bumper pull trailers are workhorses—used for moving landscaping gear, camping supplies, furniture, and everything in between—but one of the most common upgrades we help our customers with is a reliable trailer jack. As a jack supplier, I’ve installed hundreds of these myself, both for retail customers and service crews, and I can tell you it’s a project most people can tackle in a Saturday afternoon with basic tools. I’m not a certified mechanic, just a guy who’s spent years troubleshooting trailer hardware and learning what works for real people, not just instruction manuals. Let’s walk through exactly how to install a trailer jack on a bumper pull, step by step, with tips I wish someone had told me the first time I tried this. Trailer Jack

First, let’s start with the basics: choosing the right jack for your trailer. This isn’t a “one size fits all” job, and picking the wrong jack is the #1 mistake we see customers make when they come to us needing a replacement. Bumper pull trailers have tongue weights—this is the downward pressure the trailer puts on the hitch of your tow vehicle, usually 10-15% of the total trailer weight. If your trailer is 5,000 pounds total, that’s 500-750 pounds of tongue weight. Your jack needs to have a lift capacity at least matching that tongue weight, plus a little extra for safety. A lot of people grab a cheap jack from the big box store that only handles 1,000 pounds, and wonder why it bends or breaks when they’re trying to hitch up a loaded utility trailer. We carry three main types of jacks for bumper pulls: a top wind jack (most affordable, great for occasional use), a side wind jack (faster for frequent use), and a drop leg jack (perfect if your trailer sits low and you need extra clearance over the ground). I always recommend adding a swivel wheel too—when you’re not hitching, that small wheel makes it way easier to move the trailer around your driveway without lifting a finger. Take five minutes to weigh your trailer tongue before you order a jack, and double-check the length: when fully extended, the jack should reach the ground no matter how level your driveway is. If it’s too short, you’ll be stuck leaning awkwardly to hook up the trailer, and if it’s too long, it’ll drag on the ground while you’re driving.

Next, gather your tools and prep the area. You don’t need a fancy toolbox for this, just the basics: a socket set (with ¾-inch and ½-inch sockets being the most common for trailer tongue bolts), a ratchet, a wrench set, a drill with a metal drill bit if you’re working with a steel tongue, a measuring tape, a level, a jack stand (critical, please don’t skip this), and a marker. Park your trailer on flat, level ground, and if you can, chock the wheels with heavy blocks to keep it from rolling while you work. I always like to disconnect the trailer lights first—you don’t want to yank the wiring harness by accident while you’re working on the tongue. Now, locate the mounting point for your old jack, or if you’re installing a new one from scratch, pick a spot on the tongue that’s 12 to 18 inches back from the very end of the tongue. If you put it too close to the end, it’ll wobble when you lift the trailer, and if you put it too far back, it won’t reach the ground. Most trailer tongues have pre-drilled mounting holes, but if yours is an older model without, you’ll need to mark two holes spaced 3 to 4 inches apart, centered on the tongue. Hold the jack up to the tongue and double-check that it’s straight—you don’t want it angled to the left or right, which will make it hard to line up with your hitch later.

Now, the installation step, and this is where a lot of people make mistakes with drilling or bolts. If you have a pre-existing jack, first remove the old one by loosening the bolts on both sides of the tongue. Some older trailers have rusted bolts, so you might need to spray a little penetrant (like WD-40) on them and wait 10 minutes before trying to loosen them—don’t use excessive force, or you’ll twist the bolt right off and have to drill it out. Once the old jack is off, clean the area where you’re mounting the new jack with a rag to get rid of dirt, rust, and grease. If you’re drilling new holes, use a center punch to make a small indent where you marked, so your drill bit doesn’t slip. Use a metal drill bit that’s slightly smaller than the mounting bolts that came with your jack—this will make sure the bolts grip tight without stripping the threads. Drill all the way through the tongue, and if you’re working on a steel tongue, go slow to avoid overheating the bit. Once the holes are drilled, slide the mounting plate of the new jack over the holes, and thread the bolts through from the bottom of the tongue. Wait, hold on—most people forget the lock washers! You should put a lock washer and a flat washer on each bolt before threading the nut on the top of the tongue. That’s the difference between a jack that stays on for 10 years and one that falls off on a highway. Tighten the nuts with your ratchet, but don’t over-tighten them to the point that the metal of the tongue bends—snug is good, tight is better, but no need to crank it so hard you strip the nut.

Now, test the jack to make sure it works, and adjust for fit. This is the most important test step, because you don’t want to get all done installing it and realize it doesn’t reach the ground or lift the trailer properly. Crank the jack all the way down, then push it to make sure it’s sturdy—there should be no wobble. Crank it all the way up, then extend it again to check the range. If it drags on the ground when extended, you might need to get a drop leg jack, or you can add a small spacer washer between the mounting plate and the tongue to lift the jack a little higher. Next, test the weight capacity: if you have a friend nearby, ask them to help you push the trailer, then crank the jack up to lift the tongue 2 to 3 inches off the ground. It should lift smoothly without straining or making a creaking noise. If it strains, that’s a sign you got a jack with too low a capacity for your trailer, and you’ll need to replace it—we see this all the time, and we’ll always help a customer exchange a jack that’s the wrong fit, no questions asked.

I’ve learned a lot of lessons from installing jacks over the years, and I want to share some common mistakes that can turn a simple project into a headache. First, never use wooden blocks to support the trailer while you work—always use a jack stand. Wooden blocks can split or slide, and if the trailer falls, you can get seriously injured. Second, don’t skimp on the bolts. A lot of hardware stores sell generic bolts that aren’t rated for trailer use—make sure the bolts and nuts you use are grade 5 or higher, which are designed to handle heavy loads. Third, grease the jack threads before you install it, or at least once a year. Salt, dirt, and rain can cause the threads to rust, making the jack hard to crank and even seizing up completely. We sell a small tube of trailer jack grease with every jack we ship, and it’s worth every penny to use it. Fourth, check the jack after the first few trips. Sometimes bolts can loosen during the first few uses, so take five minutes a week after installation to tighten them again.

Once you’ve installed and tested your new trailer jack, you’ll notice how much easier it is to hitch up your trailer, load and unload gear, and even move it around your property without a tow vehicle. A good jack isn’t just a convenience—it’s a safety tool. If your jack breaks mid-hitch, you could drop the trailer tongue and damage your hitch, or even hurt yourself, so investing in a quality jack from a reputable supplier is always the best choice.

If you have questions about choosing the right jack for your trailer, need help troubleshooting an installation, or are ready to purchase a durable trailer jack that will last for years, feel free to reach out to our team. We’re always here to help with all your trailer hardware needs, no matter how big or small your project is.

Wheels & Tires References:

  1. Trailer Manufacturers Association. (2022). Recommended Safety Standards for Bumper Pull Trailer Components. TMA Publications.
  2. American Society of Agricultural and Biological Engineers. (2021). Design Guidelines for Trailer Hitch and Jack Systems. ASABE Standards.
  3. National Highway Traffic Safety Administration. (2020). Light Trailer Safety and Maintenance Guide. NHTSA Technical Report.
  4. Trailer Life Magazine. (2023). 10 Common Mistakes When Installing Trailer Jacks. Monthly Maintenance Feature.

Qingdao Herzhe Tools Manufacturing Co., Ltd.
Qingdao Herzhe Tools Manufacturing Co., Ltd. is one of the most professional trailer jack manufacturers and suppliers in China. We have world-leading production equipment and strong manufacturing capabilities. Please feel free to buy advanced trailer jack at competitive price from our factory.
Address: No.406 Shuangfushan Road, Baoshan Town, Qingdao CHINA
E-mail: herzhetool@163.com
WebSite: https://www.herzhetoolsmfg.com/