{"id":899,"date":"2026-11-22T04:09:51","date_gmt":"2026-11-21T20:09:51","guid":{"rendered":"http:\/\/www.angazasingers.com\/blog\/?p=899"},"modified":"2026-11-22T04:09:51","modified_gmt":"2026-11-21T20:09:51","slug":"how-to-purge-air-from-a-water-cooled-chiller-4915-f896e6","status":"publish","type":"post","link":"http:\/\/www.angazasingers.com\/blog\/2026\/11\/22\/how-to-purge-air-from-a-water-cooled-chiller-4915-f896e6\/","title":{"rendered":"how to purge air from a water cooled chiller"},"content":{"rendered":"<p>Hey there, <a href=\"https:\/\/www.headpowerac.com\/water-cooled-chiller\/\">Water Cooled Chiller<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.headpowerac.com\/uploads\/202021867\/small\/purifying-type-combined-ahu202003161027366597920.jpg\"><\/p>\n<p>If you\u2019ve ever worked with water cooled chillers, you know that tiny bit of air in the system can turn into a massive headache real quick. It throws off cooling efficiency, makes weird gurgling noises, and even wears out parts way faster than it should. As someone who\u2019s spent the last decade troubleshooting these things (and selling them, duh), I\u2019ve seen way too many unit failures that could\u2019ve been avoided with a simple purge. Today I\u2019m walking you through exactly how to purge air from a water cooled chiller\u2014no fancy jargon, just the real deal stuff I tell our customers when they call panicking at 2 a.m.<\/p>\n<p>First, let\u2019s get on the same page: why does air even get in there? Mostly it comes from when you first fill the system (air gets trapped in pipes and heat exchangers), or when you\u2019re topping off water because of a leak, or even dissolved in the water itself that comes out of solution when the system heats up. That dissolved air is the sneaky stuff\u2014It\u2019s not just the big bubbles you can see, it\u2019s the tiny micro-bubbles that stick to the evaporator tubes and act like insulation. That means your chiller has to work harder to cool the water, which hikes up energy bills and shortens its lifespan. No bueno.<\/p>\n<p>Before you dive in, grab your basics: a pair of work gloves (you\u2019ll be dealing with water that\u2019s either super cold or hot, depending on where you are), a small bucket, a flathead screwdriver, and make sure the chiller is turned OFF. I know it\u2019s tempting to just wing it while it\u2019s running, but trust me\u2014getting a burst of cold water or a surprise spray isn\u2019t worth it. Also, check that the water level in the expansion tank is where it should be (your chiller manual will say, but usually it\u2019s about 12-15 PSI). If it\u2019s way off, fix that first before purging air\u2014you don\u2019t want to overfill later.<\/p>\n<p>Now, let\u2019s break this down step by step, starting with the easiest purge spots first, then moving to the tricky ones.<\/p>\n<ol>\n<li>\n<p><strong>Bleed the High-Point Air Vents First<\/strong><br \/>\nEvery water cooled chiller system has these little brass or plastic vents (we call them \u201cbleed valves\u201d) at the highest points. These are your first stop. They\u2019re usually on the top of the evaporator, the condenser, and any horizontal pipes that run uphill. Why high points? Because air rises, so that\u2019s where all the big bubbles are hanging out.<br \/>\nTake your flathead screwdriver, slowly turn the vent counter-clockwise just a quarter turn\u2014don\u2019t yank it open all the way, that\u2019ll cause a geyser and make a mess. You\u2019ll hear a hissing sound first\u2014that\u2019s the air escaping. Keep it open until all the hissing stops and a steady, thin stream of water comes out, no sputtering. Then close the vent tight, clockwise. Do this on every single high-point vent. I see people skip one all the time, and that\u2019s why their cooling is still garbage a week later. Pro tip: mark which vents you did with a sticky note if you\u2019re working alone, so you don\u2019t miss any.<\/p>\n<\/li>\n<li>\n<p><strong>Bleed the Pump Air Vent<\/strong><br \/>\nThe chiller\u2019s water pump is another spot where air loves to hide. Most pumps have a small bleed screw right on the top housing. This is super important because if the pump has air, it won\u2019t circulate water properly\u2014you\u2019ll get dead zones in the system, and the chiller will trip on high discharge pressure.<br \/>\nSame drill here: turn the screw slowly. Again, listen for the hissing. Once you get a solid flow of water, close it up. This only takes like 30 seconds, but don\u2019t skip it. I\u2019ve had a customer call saying their chiller was freezing up, and it turned out they forgot the pump vent. Fixed in 2 minutes.<\/p>\n<\/li>\n<li>\n<p><strong>Purge the Expansion Tank<\/strong><br \/>\nWait, expansion tank? Yeah, that rubber or steel tank that balances water pressure is a secret air trap. Sometimes air accumulates in the bladder (if it\u2019s a bladder tank) or the tank itself, which makes it not work right. If your system has a diaphragm tank, there\u2019s usually a tiny air valve on the top, like a bike tire valve. Turn the chiller off, make sure the pressure is at the recommended level (again, manual is your friend), then briefly press the valve core to let any trapped air out\u2014don\u2019t do it for more than a second, you don\u2019t want to lose too much water. If it\u2019s a non-bladder tank, there might be a drain valve on the bottom; open it a tiny bit to let a little water run out, which will push air up and out, then close it.<\/p>\n<\/li>\n<li>\n<p><strong>Run the System and Purge Micro-Air (The Tricky Stuff)<\/strong><br \/>\nOkay, so you\u2019ve done all the big vents, but that\u2019s probably not enough. The micro-bubbles are still in the water, and they\u2019ll come out when the system is running. Now\u2019s the time to start the chiller, but on LOW load. Don\u2019t turn it on full blast\u2014run it at 20-30% capacity for 15-20 minutes. This lets the water circulate slowly, giving the micro-bubbles time to rise to the vents you already opened.<br \/>\nWhile it\u2019s running, go back through all the vents one more time. You might hear a little more hissing this time, that\u2019s the micro-bubbles escaping. Do this 2-3 times until all you get is clear water no sputtering. Also, keep an eye on the pressure gauge on the chiller panel. If it drops after purging, you can top off the water with demineralized water (tap water has minerals that will gunk up the heat exchanger, trust me) to get it back to the right PSI.<\/p>\n<\/li>\n<li>\n<p><strong>Final Check for Hidden Air<\/strong><br \/>\nAfter you\u2019re done, wait an hour, then check again. Sometimes air gets into the pipes when the system heats up, especially if you have long runs. If you start hearing gurgling noises from the pipes or the chiller trips on low temperature, you missed a spot. Don\u2019t panic\u2014just go back to the vents and bleed again.<\/p>\n<\/li>\n<\/ol>\n<p>Now, let\u2019s talk about common mistakes I see people make all the time. First, opening the vents too wide. That causes water to spray all over electrical parts, which is a fire hazard and can ruin your chiller. Take it slow, quarter turns only. Second, not using demineralized water. Tap water has calcium and chlorine, which build up on the heat exchanger over time and make your chiller less efficient. We always tell our customers to buy pre-mixed demin water for top-offs. Third, skipping the pump vent. That\u2019s like forgetting to check your oil before a road trip\u2014you\u2019re asking for trouble. Fourth, running the chiller at full load right away. That just stirs up the micro-bubbles and makes them harder to get out.<\/p>\n<p>Wait, also\u2014what if you have a chiller with an automatic air vent? A lot of newer models have these instead of manual vents. Do you still need to purge? Yeah, sometimes the automatic ones get clogged with gunk, so you might need to manually open them to clear the blockage. They\u2019re usually on the same high points, just a plastic cap you can twist off gently.<\/p>\n<p>Another thing: if you just installed a new chiller, you might need to purge more than usual. Install lines can have extra air trapped in them. Plan to do two full purge cycles in the first week after installation to make sure all the air is out.<\/p>\n<p>Now, how often should you purge air? It depends on how much you use the chiller, but at least once a year before the cooling season starts. Also, if you notice a drop in cooling performance, weird noises, or pressure swings, purge right away\u2014don\u2019t wait for it to break down.<\/p>\n<p>As a chiller supplier, I can\u2019t stress enough how important proper air purging is. We\u2019ve had customers come to us after trying to do it themselves and messing up, and it\u2019s way more expensive to fix a broken chiller than to do the purge right the first time. If you\u2019re not comfortable doing this yourself, just reach out\u2014we have techs on call who can come out and do it for you, no hassle.<\/p>\n<p>At the end of the day, purging air from a water cooled chiller isn\u2019t rocket science. It\u2019s just paying attention to the small details, taking it slow, and not skipping steps. The time you spend doing it saves you hundreds (or thousands) in energy bills and repair costs later.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.headpowerac.com\/uploads\/202021867\/small\/100kw-ground-source-heat-pump-air-conditioner56003999288.jpg\"><\/p>\n<p>If you\u2019re dealing with persistent air issues or need a new chiller that\u2019s built to hold air out better for longer, feel free to get in touch to chat about your needs. We\u2019re here to help you keep your system running smooth all year round.<\/p>\n<p><a href=\"https:\/\/www.headpowerac.com\/screw-chiller\/\">Air cooled Screw Chiller<\/a> REFERENCES<\/p>\n<ol>\n<li>Carrier Commercial HVAC: Water Cooled Chiller Maintenance Guide<\/li>\n<li>ASHRAE Handbook &#8211; HVAC Systems and Equipment<\/li>\n<li>Trane Chiller Operation and Troubleshooting Manual<\/li>\n<\/ol>\n<hr>\n<p><a href=\"https:\/\/www.headpowerac.com\/\">Guangdong Head-Power Air-Conditioning Co., Ltd.<\/a><br \/>Guangdong Head-Power Air-Conditioning Co., Ltd. is one of the most professional water cooled chiller manufacturers and suppliers in China, specialized in providing high quality products made in China. We warmly welcome you to buy customized water cooled chiller at low price from our factory. Contact us for quotation.<br \/>Address: Shiling Chenbian Section, 321 National Highway, Shishan Town, Nanhai District, Foshan, Guangdong, China.<br \/>E-mail: info@china-headpower.com<br \/>WebSite: <a href=\"https:\/\/www.headpowerac.com\/\">https:\/\/www.headpowerac.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Hey there, Water Cooled Chiller If you\u2019ve ever worked with water cooled chillers, you know that &hellip; <a title=\"how to purge air from a water cooled chiller\" class=\"hm-read-more\" href=\"http:\/\/www.angazasingers.com\/blog\/2026\/11\/22\/how-to-purge-air-from-a-water-cooled-chiller-4915-f896e6\/\"><span class=\"screen-reader-text\">how to purge air from a water cooled chiller<\/span>Read more<\/a><\/p>\n","protected":false},"author":166,"featured_media":899,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[859],"class_list":["post-899","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-water-cooled-chiller-43fb-f8d15a"],"_links":{"self":[{"href":"http:\/\/www.angazasingers.com\/blog\/wp-json\/wp\/v2\/posts\/899","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.angazasingers.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.angazasingers.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.angazasingers.com\/blog\/wp-json\/wp\/v2\/users\/166"}],"replies":[{"embeddable":true,"href":"http:\/\/www.angazasingers.com\/blog\/wp-json\/wp\/v2\/comments?post=899"}],"version-history":[{"count":0,"href":"http:\/\/www.angazasingers.com\/blog\/wp-json\/wp\/v2\/posts\/899\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.angazasingers.com\/blog\/wp-json\/wp\/v2\/posts\/899"}],"wp:attachment":[{"href":"http:\/\/www.angazasingers.com\/blog\/wp-json\/wp\/v2\/media?parent=899"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.angazasingers.com\/blog\/wp-json\/wp\/v2\/categories?post=899"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.angazasingers.com\/blog\/wp-json\/wp\/v2\/tags?post=899"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}